Emergency Light Conversion Kits

Emergency Lighting Kits Ideal for integrating into existing control gear. Supplied with a fused terminal block and pre-cut connection wires.,The modules can be tuned specifically to the lamp, giving better performance for the cell capacity. Lamp compatibility/Ballast Lumen Factor Stock No. T5 T8 2-D PL-L PL-C PL-S 466-3330 4 / 0.59 15 / 0.32 21 / 0.29 18 / 0.33 18 / 0.28 5 @ 0.46 6 / 0.62 18 / 0.32 28 / 0.21 24 / 0.19 26 / 0.23 7 @ 0.56 8 / 0.62 30 / 0.15 38 / 0.18 34 / 0.17 - 9 @ 0.44 13 / 0.30 36 / 0.15 - 36 / 0.18 - 11 @ 0.47 14 / 0.25 - - - - - 21 / 0.25 - - - - - 22 / 0.18 - - - - - 466-3346 n/a 70 / 0.09 n/a n/a n/a n/a Note: Wattage/Ballast Lumen Factor shown for applicable lamp sizes Lamp compatibility/Ballast Lumen Factor Stock No. T8 466-3346 70/0.09 Note: Wattage/Ballast Lumen Factor shown for applicable lamp size Note Nominal tube diameter - T5=16mm, T8=26mm, T12=38mm Conversion Kits Charger/inverter modules for converting fluorescent luminaires into emergency lighting units.,The module and battery packs fit inside most modern fluorescent batten fittings. For luminaires that have limited internal dimensions or that have internal temperatures above 50°C, remote mounting boxes are also available. The remote box is also suitable for converting double luminaires into emergency units, however only 1 tube will operate under emergency conditions. Two live supplies are required for standard operation, one switched, one unswitched. Failure of the unswitched supply operates the changeover circuit bringing on the battery supply. A red LED is supplied with the module for fitting into either the luminaire or remote box, to indicate a healthy battery charging state. The nickel-cadmium battery packs are protected against deep discharge.

16W 2D Conversion Kit Integrated high frequency ballast and emergency lighting unit Replaces existing control gear Includes 2D lampholder and mains terminal block LED supplied with leads and support bracket Note The batteries must not exceed 50°C. A minimum internal size of 300mm dia x 100mm is recommended to prevent overheating. Conversion Kits Charger/inverter modules for converting fluorescent luminaires into emergency lighting units.,The module and battery packs fit inside most modern fluorescent batten fittings. For luminaires that have limited internal dimensions or that have internal temperatures above 50°C, remote mounting boxes are also available. The remote box is also suitable for converting double luminaires into emergency units, however only 1 tube will operate under emergency conditions. Two live supplies are required for standard operation, one switched, one unswitched. Failure of the unswitched supply operates the changeover circuit bringing on the battery supply. A red LED is supplied with the module for fitting into either the luminaire or remote box, to indicate a healthy battery charging state. The nickel-cadmium battery packs are protected against deep discharge.

Emergency Lighting Kits Ideal for integrating into existing control gear. Supplied with a fused terminal block and pre-cut connection wires.,The modules can be tuned specifically to the lamp, giving better performance for the cell capacity.

RS PRO 70 W Emergency Light Conversion Kit, 150 mm x 44 mm x 35 mm With this emergency light conversion kit from RS PRO, you can convert fluorescent luminaires without compromising on safety. Failure of the light's unswitched supply will switch the light onto a battery supply. The module and battery packs fit inside most modern fluorescent batten fittings. With a fused terminal block and pre-cut connection wires included, this kit is suitable for integrating into existing control gear. In addition, the module can be tuned specifically to the lamp, which offers better performance for the cell capacity. It comes with an LED for fitting into the luminaire to indicate battery charge. The kit has been tested against international standards for safe lamp control gear (EN 61347-2-7), safe luminaires (EN 60598-2-2) and suitability for conversion to emergency lighting (ICEL 1004). It also meets requirements on automatic testing (BS5266-1:2005/IEC62034). This kit can be used for converting luminaires to emergency lighting in premises of all kinds. Features and Benefits • Emergency light conversion kit • Length of 150 mm • Width of 44 mm • Height of 35 mm • Fixing centres 140 mm apart • Maximum wattage of 70 W • Voltage rating of 220-240 V ac at 50/60 Hz • Maximum supply current of 40 mA • Maximum operating temperature of +50˚C • Minimum operating temperature of 0˚C • Maximum case temperature of +70˚C • Conductor size of 0.5 mm² to 1.5 mm² • M4 mounting screws • Meets standard EN 61347-2-7 as safe lamp control gear • Complies with standard EN 60598-2-2 as a safe luminaire • Conforms to ICEL 1004 on conversion to emergency lighting • Meets BS 5266-1:2005/IEC 62034 on automatic testing • Conforms to ANSI/ESD S20.20:2014 and BS EN 61340-5-1:2007 Electrostatic Control Standards • RoHS (Restriction of Hazardous Substances) compliant RS PRO RS PRO is our own brand range and brings you a wide range of high-quality, great value products offering you more choice. Trusted by engineer...

RS Emergency LED Mini Downlighters Non-Maintained These non-maintained, emergency LED mini downlighters conversion kit can be used in a variety of different ways, to provide a simple yet adaptable lighting solution. The LED mini downlighters are available in versions of 1W, 3W and 5W. Ideal applications of these LED emergency mini conversion kit are in corridors, offices and retail. 1W, 3W and 5W non-maintained self-contained LED 3.6V 1.5Ah (1W) 3.6V 3Ah (3W) 3.6V 4.5Ah (5W) NiMH battery pack 24 hour charging, 3 hour duration E¬cient re ector design Recessed mounting brackets included

RS Emergency LED Mini Downlighters Non-Maintained These non-maintained, emergency LED mini downlighters conversion kit can be used in a variety of different ways, to provide a simple yet adaptable lighting solution. The LED mini downlighters are available in versions of 1W, 3W and 5W. Ideal applications of these LED emergency mini conversion kit are in corridors, offices and retail. 1W, 3W and 5W non-maintained self-contained LED 3.6V 1.5Ah (1W) 3.6V 3Ah (3W) 3.6V 4.5Ah (5W) NiMH battery pack 24 hour charging, 3 hour duration E¬cient re ector design Recessed mounting brackets included Emergency Light Fittings There are two basic types of emergency lighting luminaires - maintained and non-maintained. Maintained,These luminaires have the advantage of being able to be switched between the maintained function (lamp illuminated at all times) and non-maintained (lamp off until power supply fails), making them ideal for applications such as corridors, workshops and permanently illuminated emergency exit signs.The maintained luminaires also have the facility of being switched in banks of up to ten units. Non-maintained,These luminaires are only illuminated on a failure of the mains supply. Ideal for emergency exits, switchrooms and storage areas.