Discounted Products

Plug-in Reducer - KQG2 Series SMC’s KQG2 stainless steel range provides engineers with a choice of high performance, lightweight, compact push in fittings for when resistance to corrosion, chemicals and high temperatures is vital. 30% smaller and 62% lighter than the existing KQG range and available to tubing diameters from 3.2 to 16mm. Suitable for use with compressed air, water, steam and able to perform across a diverse range of pressure (-100kPa to 1MPa) and temperature conditions (-5°C to +150°C). Threaded, Tube-to-Tube & Adaptors - SMC KQG2 KQG2 SUS316 Stainless Steel Fittings SMC KQG2 series one-touch pneumatic fittings are manufactured from SUS316 stainless steel, offering corrosion resistant properties that are better than grade 304 stainless steel. SUS316 stainless steel offers higher pitting and corrosion resistance properties, and is especially suitable for chloride environments. Applications KQG2 series one-touch fittings make use of FKM seals and may be used with a variety of tubing including nylon, soft nylon, polyurethane, polyolefin, FEP and PFA. The fittings are suitable for use with steam and are grease-free.

P&F Dual Channel Zener Diode Barriers Using a dual channel barrier impedes a direct grounding of the intrinsically safe circuit. The ground is only made in the event of a failure, if the zener diodes conduct. This circuit also suppresses influences of external circuits. Typical application - thermocouples Isolation Barriers Pepperl+Fuchs shunt zener diode barriers are for use as safety interfaces between intrinsically safe and non-intrinsically safe circuits. They are manufactured from Makrolon® and designed to conduct electrical signals - in either direction - between safe and hazardous areas and to limit the amount of energy which can be transferred from a safe to a hazardous area in the event of fault conditions occurring in the safe area. All systems shown are licensed for [EEx ia] IIC Class 1, Div1, Groups A-G

DeWALT 18V XR LI-ION BRUSHLESS COMPACT DRILL DRIVER The DCD791 is available in three different set options: 136-2870 814-0440 European plug 124-8953 UK plug Features and Benefits: 814-0440 124-8953 Typical Application: Supplied with: 814-0440 124-8953 FAQs: How many batteries are included in the set? 814-0440 124-8953 DeWalt Power Tool Batteries Is the chuck replaceable?

IP68 3-Pole Self Latching Tested and approved to IEC 61984:2001 and IP 68 Rated to 2 bar Collar mechanism allows fast connection or release of the connector The Connector and Internal Screw Terminals can be easily assembled without the need for special tooling Positive keyways to prevent mis-assembly Sealing Caps available to maintain IP68 rating when separated (see, for example, stock number 478-7694 ) Cable entry points offer high cable retention and prevent cable twist during installation Dimensions (mm): L 150, Dia 37 (mated)

The Lovato product is a rotary cam changeover switch with 4 poles. It has front mounting with black handle. Suitable for circuit connection, changeover, switching ON and OFF as well as motor starting Square shaped contact body Possibility of side by side installation

Screw Cap Choice of release caps Nylon body and cap, UL94-VO rated Low insertion resistance Protection: PC2 Approvals UL Panel Mounting CATEGORIES OF PROTECTION AGAINST ELECTRIC SHOCK,PC1: No integral protection against electric shock. If required, designers must provide additional protection against electric shock on equipment.,PC2: With integral protection against electric shock. Fuse-holders shall have live parts inaccessible to IEC529 standard test finger, when fully assembled, without fuse carrier or fuse in place and when fuse carrier, with fuse is being inserted or withdrawn.,PC3: With integral protection against electric shock. Fuse-holders shall have live parts inaccessible to IEC529 1mm diameter rigid test wire when fully assembled, without fuse carrier or fuse in place and when fuse carrier, with fuse is being inserted or withdrawn.

CONN BASE SIDE ENTRY SZ10B M20

Panel Plugs & Sockets Male and female 4 way panel mount receptacles. Stock no. 351-443 offers the option to convert glanded switches into connector versions by simply screwing the PG13.5 threaded end of the receptacle into the appropriate proximity switch.

The Sick clamping bracket is used for rods with a diameter of 12 mm. Made up of aluminium Note Product details cover the whole product family. For details on the specifications for this individual product, please refer to the datasheet.

Bear-tex Hand PadSheet size 150 x 230mm

RS German Colour Range Crimp Bootlace Ferrules German colour range insulated crimp ferrules made from bright tinned copper with polypropylene insulating sleeves that accept tri-rated and 2491X cables. These german colour range crimp bootlace ferrules provide a neat end termination to multi-stranded wires and reduce the possibility of wire strands short circuiting adjacent terminals and ensure a positive connection when used with terminal blocks and captive terminals. These crimp bootlace ferrules are available with a variety of pin lengths and wire sizes. For suitable crimp tool and die see stock numbers 848-391 and 848-420 Note Length quoted is Pin Length Approvals -

100S-C, 3 Pole Safety Contactors 2N/O & 3N/C The Bulletin 100S-C safety contactors provide mechanically linked positively guided contacts, required in feedback circuits of modern safety applications. The mechanically linked N.C. auxiliary contacts will not change state when a power pole welds. In addition, the gold-plated bifurcated auxiliary contacts are ideally suited for low-energy applications or feedback control circuits with multiple series-connected N.C. auxiliary contacts. Redundant contactors to isolate motor (hazardous motion)Positively guided main contactsRed contact housings for easy identification as safety deviceProtective cover prevents manual operation - yet the window allows visible ON/OFF statusNote DC versions incorporate a diode protection circuitSafety Contactor

PowerTOP Connectors Spring loaded covers protect contacts when not in use and latch on to mating plugs Easy to assemble as terminals are open to receive bare conductors which are accessible from one direction External cable clamp simplifies installation and provides support of cable preventing movement around seal Note For Plugs see example 236-0023 Mennekes PowerTOP Glanded Entry HQ Range – IP44 and IP67 Plugs, sockets, appliance inlets and interlocked sockets conforming to the latest requirements of British and European standards. The insulator outer casing and interiors are manufactured from Amaplast (nylon 6) 16/32A, Amelan 63 / 125A for excellent mechanical performance. This material provides good electrical insulation and will meet the requirements of most industrial environments. Contact tubes and pins are made of brass. To prevent incorrect connection, the earth contact is in a different position, relative to the safety key way on each socket outlet, for each voltage. All types are colour coded by voltage and are suitable for 50/60Hz operation. Products are type tested to VDE.

High specification degreaser for electrical & electronic componentsPowerful citrus degreaser for difficult contaminants such as flux, solder mask and adhesives from electrical components and equipment. Designed to degrease PCBs and equipment, it will also remove electrical greases from rewinds and motors. Formulated to a high di-electric strength 53,000v. Low volatility. Flashpoint 45 C. Special Order Item Extended Lead Times & Minimum Order Quantities.

OEP 25W to 65W Single/Triple Output Switch Mode Desktop Power Supply - PSU & SPU Series External switch mode power supplyProtected against short circuit, overload, over voltage and over temperatureLED indication of power onFully enclosed plastic caseEMI emission levels meet FCC Class 'B'3-pin IEC320 universal inputFitted with approx. 150cm output lead terminated with DIN connectorNote Non Compliant For Industrial Use Only, not in scope of Regulation (EC) No 125/2009Approvals UL listed / UL listed for Canada, TUV

Lifeline 4 Rope Pull Switch The Lifeline 4 rope pull switch, also known as a cable pull switch or grab wire switch, can be installed along or around awkward machinery such as conveyors and provides constant emergency stop access. The positive mode mechanism helps ensure that the contacts are immediately latched open on actuation and can only be reset by the intentional action of turning the blue reset knob. The design of this safety switch also protects against nuisance tripping and the effects of thermal expansion. A mushroom head emergency stop button is included on the Lifeline 4 to provide E-Stop access even at the extreme ends of the span. The cable status indicator makes this rope pull switch easy to set up and maintain for spans up to 125m. Switches up to 125m span Universal mounting and operation Lid mounted emergency stop button, designed to conform to ISO 850 Switch lockout on cable pulled and cable slack Cable status indicator on switch lid Sealed to IP66 Tension force 188 N lock-out, 103 N running Operating Force Operating temperature -25°C to +80°C Safety contact gap >2 x 2mm Rated at 500V ac/1A, 250V ac/2A, 100V ac 5A Heavy duty weatherproof die-cast aluminium alloy (LM24) yellow case Stainless steel eye nut, glass filled nylon indicator CE marked in compliance to relevant European Directives Note For suitable rope kits see stock no. 366-3878 typically. Approvals BG, UL listed for Canada and US. Standards Designed to conform to EN418, EN292, EN60947-5-1, ISO 13850, BS 5304.

CBL CLAMP P-TYPE BLACK FASTENER

Tygon® Fuel & Lubricant Tubing F-4040-A Extremely flexible, compatible with most petroleum based products Resists embrittlement, swelling, cracking & hardening Resistant to Ozone & UV light Applications vary from small engine fuel lines to coolant transfer

AC/DC CONVERTER 24V 240W

SWITCH SNAP ACT SPDT 100MA 125V

RS PRO RS-A3305P Series Bench Power Supply Introducing the RS PRO RS-A3305P Series Bench Power Supply. This high-performance D/C power supply allows users to work without additional noise being created by the power supply due to the low noise level and ripple function. This bench power supply is of an industrial grade which allows to work for long periods of time, without compromising the quality of the tests that are being run. This bench power supply is a high-quality, versatile piece of equipment that can be used for a variety of applications and can be bought as a non-calibrated or calibrated ( or UKAS Calibration) machine.Features and Benefits: Complete programmable allowing users to self-define voltage and current under rated power conditions to satisfy them with wider voltage and current operational ranges Industrial grade power supply unit to allow for load testing for greater periods of time without impacting testing Low noise and ripple feature that allows for greater clarity and less noise in the working environment 5 sets of parameters can be stored and recalled for frequent testing 100 sets of stored parameters inside for programmable recall CV / CC constant voltage and constant current modes The remote measurement terminal compensates the voltage drop of the wire Built-in USB and RS-232 Interface giving greater flexibility for use 10 mV / 1 mA resolution Available for RS and UKAS calibrationApplications: A bench power supply is an essential piece of equipment if you do a lot of electronics or other powered projects on your bench and need a reliable source of power at different voltages. They are very useful tools in testing circuits, as they allow you to adjust the voltage to a specific value depending on what project you are working on.The most common and versatile regulated DC power supply is the constant current (CC)...