MODMYPI LTD

Uninterruptible Power Supply and I2C Control HAT for Raspberry Pi, ModMyPi Uninterruptible Power Supply and I2C Control HAT for Raspberry Pi, ModMyPi UPS PIco HV3.0 A Stack 450 is an uninterruptible power supply by ModMyPi for Raspberry Pi models A+/B+/2/3. The power supply comes with an embedded measurement system which checks the powering of the Pi and includes 450 mAh LiPo battery. LiPo battery is designed for a safe shutdown during a power cut. If a power failure is detected on the Raspberry Pi, the UPS Plco automatically switches to the Pi battery source once the power is restored. Raspberry Pi is not included and can be purchased separately at RS(Raspberry Pi 3 - RS 8968660 and previous models) UPS Plco needs no external power and fits within the footprint of Raspberry Pi. Features Raspberry Pi HAT Compliant Plug and Play Smart Uninterruptible Power Supply (UPS) with Integrated 450 mAh LiPo Battery (10-15 min of Power Back-Up) Interrupt Driven Interaction (Low Memory/CPU Use) Software Driven Email Broadcasting Intelligent Automatic Charger with Power Tracking No Additional External Power Required Supports LiPo and LiFePO4 (Long Life) Batteries 5 V 3A Power Backup for even the most demanding Pi 3 set-up. Integrated Hardware Real Time Clock (RTC) with battery backup File Safe Shutdown Functionality - Single Button On/Off Raspberry Pi Zero/B+/2/3 Activity Pin Status Monitoring - Powering Voltage, UPS Battery Voltage/Current and Temperature I2C PICo Interface for Control and Monitoring RS232 Raspberry Pi Interface for Control and Monitoring 2 way XTEA Based Cryptography User Software Protection 2 Level Watch-dog Functionality with FSSD and Hardware Reset Stackable Header for Add-On Boards (Header Included) Boot Loader for Live Firmware Update Events Triggered RTC Based System Actions Scheduler (ON/OFF based on RTC or Events e.g Voltage, RS232 data, A/D, IR) External 5 V @ 750 mA Powe...

PIco Fan Kit for Raspberry Pi, ModMyPi PIco FAN Kit is an Advanced Active Cooling System for the Raspberry Pi and is easy to install by using the UPS Plco(Uninterruptible Power Supply and I2C HAT). The kit with the use of UPS Plco supervising circuits regulates any overheating of the Raspberry Pi board. Also has an embedded temperature measurement system which monitors and regulates the temperature by switching the fan on and off. Uninterruptible Power Supply and I2C HAT are available to purchase RS 1270208 Raspberry Pi is not included and can be purchased separately (Raspberry Pi 3 - RS 8968660 and previous models) Features Powered from the J8 (P1) connector of the Raspberry Pi® via UPS PIco PWM FAN speed regulation 1 RED LED-based information system (Light Red - hot, Light Red – cold) Full control over the system via I2C interface (The PIco Interface) Kit Contents Micro Fan with cable Set of 4 tree clips required for PIco FAN mounting UPS PIco PCB Set of 4 rubber washers required for the PIco FAN mounting UPS PIco PCB TO-92 temperature sensor 2 mm PCB connector for the FAN

ModMyPi PiOT Relay Board for Raspberry Pi, ModMyPi The ModMyPi PiOT (Pi of Things) relay board is designed well without any complex wiring and jumper configurations for the Raspberry Pi. Also the on-board PIC makes configuration faster, easier and safer. The PiOT relay board can be connected on top of Raspberry Pi or by a GPIO ribbon cable (not included). Fully assembled board is ready to plug and get started. Note: Raspberry Pi is not included and can be purchased separately (Raspberry Pi 3 - RS 8968660 and previous models) Warning: Relays can be used to switch large voltages and currents. Be careful when undertaking any work with this type of power - it can kill. Features 4 x Omron G5LA-1 Relays for Switching up to 10A @ 250 V ac, or 10A @ 24 V dc 4 x Tactile Buttons for GPIO/Relay Bonding Two-Digit 7 Segment Display for Visual Feedback and Setting Control Micro-controlled GPIO/Relay Setting and Switching (No Jumpers Required!) 40 point Raspberry Pi GPIO Modelled Input 5 V and 3.3 V Input Compatible Low Holding Current via PWM ∼ 100 mA per Relay Board Stackable Relay Board (Up to 5 without External Power) Multiple Start-Up Modes to Negate Boot GPIO Chatter (Delayed/Handshake) Pi Zero Mounting Points

Heatsinks for the Raspberry Pi, ModMyPi ModMyPi Raspberry Pi Heatsink Kit consists of two aluminium heatsinks that are suitable for Raspberry Pi boards. The heatsinks has a thermal adhesive tape to help clamp and secure each heatsink down by creating a perfect heat-transfer bond. Heat sinks are available in various anodised colour finish. Features: •Keep your Raspberry Pi cool without the need for noisy fans •Extend the life of your Raspberry Pi and reduce the risk of hardware failure •2 x Aluminium Heatsinks •Compact and able to fit in most Raspberry Pi Cases (Including the ModMyPi case) •High-quality Thermal Adhesive Tape for easy application •Thermal Resistance 25°C/W •Large Broadcom CPU Heatsink - 14 x 14 x 14 mm •Medium Ethernet Controller Heatsink - 10 x 10 x 10 mm